Conference napalm::musclecars

    I have a 67 Camaro Conv. 327 4 speed and I am looking for front wrap
    parts, the chrome pieces that go around the windshield and/or anything
    that may help me with the restoration.
    
    STEVE SPEARMAN
    COMET::SPEARMAN
    DTN-522-2443
    COLO. SPRINGS AREA

    for a 76 Camaro, where can I find a patch panel for below the battery
    tray, between the front of the fender well to the front wall of the
    car?
    Matt

    LEON MEINERS
    COGITO::MEINERS
    DTN-287-3501
    
    Buy A HOT ROD Mag or CAR CRAFT there's ad's in them for Chev obso. 
    parts all the time. Either that or go to your local Chev Dealer.
    You'll be suprised at the parts you can still get for the old cars.
    
    L.M.

    I am looking for the front frame clip off a 1970 to 1980 Camaro,
     or Firebird. Would like the suspension and steering intact.
    Don't want to pay an arm and a leg either!
    
    DTN 291-7516
    CIMNET::Cail
    

         
                  Hey I've got a good 70 camaro sub. needs springs.
        through in a 10 bolt rear with it for $75 you pick them up.
                      Chris Foster 
                      572-2403 (dtn) 2nd shift
                      413-527-0651  home (sometimes)               
                                          

    have you tried richmond gear?  they are the best and run 150-175 new. 
    jeggs is one supplier. i don't have a number for richmond.

             <<< SEATTL$1$DUA3:[NOTES$LIBRARY]DRAG_RACING.NOTE;1 >>>
                                -< DRAG_RACING >-
================================================================================
Note 25.0                         Parts Wanted                        No replies
SEATTL::BERRYDO "Shiny side UP"                      13 lines   2-NOV-1991 12:30
--------------------------------------------------------------------------------
    Wanted:	1 Set of aluminum wheels
    			Chevy bolt pattern
    			15" X 10" 
    		     or 15" X 12"
    Must have 6" offset (backing surface to edge of wheel)
    May be drilled for slicks.
    matching fronts would be nice also, 14" X 3",4",5"
    
    
    Don Berry
    SEATTL::BERRYDO
    DTN 545-4539
    Home (206)-347-1431

    
    Help Needed:
    
    I'm in search for LG Journal 302 Crankshaft.
    
    Dan Sullivan
    dtn 237-2091

    Anybody have an 800 # for a place that sells Chevy body parts called
    "Harmons" (sp?).  I believe that it's somewhere in the mid-west. 
    I'm looking for a rear body mount for a full size '62  Impala.     
    
    Or.....have any recommendations for any place that they've done business 
    with?
    
    	Reply here; drop me a note; or call.
    
    			Steve George
    			Druid::George
    			DTN 232-2247

    HARMONS, INC.
    
    BOX 6J, US 27N., GENEVA, IN 46740
    (219)368-7221
    

    Tom,
    	Good luck in your search for a used head.  When I had the heads
    redone in my truck the shop found the normal cracks around the
    exhaust valve seats.  400 small block heads are hard to find and
    even harder if you want good ones.  My search took place all over
    New England, maybe you'll have better luck in Co.  What I ended
    up doing was using 350 heads, the only difference is the steam holes
    in the 400 heads.  The shop just drilled the steam holes in the new
    350 heads and I was in business.  This was on a '78 400 small block,
    you should have the same flexibility (I think) on a '69/'70, it
    might even be cheaper finding a set of 350 heads than finding a 
    good 400 head. FWIW
    
    bob

    Hi,,,
    I checked my spare part collection this weekend, and the 400 heads that
    I have are #598 castings. I believe they are either 1970 or 71's as
    they came off a 4 bolt block. They are 194, 160's....  Make me an
    offer. 
    
    
    				Brian...

    
    		Restoring a 1968 corvette convertible
    		_____________________________________
    
    	Need parts.....327 block #3914678
    		       Dist./w tach drive
    		       Intake #3919803
    		       ex. man #3872765
    			"   "  #3872778
    		       Radio and etc.
    
    	If you have anything or a lead on any parts, I'd sure appreciate
    
    	it.   Doing a frame up restoration. Someone had replaced the 327
    
    	with a 350 and put BIG  'glass flares around the rear wells. This
    
    	is a lot of work!  Thanks for any help.
    
    					Jim    dtn243-2516
    

    Wanted:  C-clip axle shaft from a 68-72 A-body Chevy 12 bolt rear end.
             Hollander # 913. Preferably in the New England area. I can get
             them from Moser new, but would prefer a good used one.
    
             Chris Roche
             dtn 285-3809
       

    Wanted: 8.5" 3:55 to 3:73 ring and pinion for GM 10 bolt. Do not
            need a complete rear end or carrier but will consider all.
    
    Chris Roche
    CRISTA::ROCHE
    285-3809

    Looking for a 68-69 El Camino. Must be rust free. Does not need to
    be running or even have a drivetrain, but should be fairly complete
    sheetmetal wise. Prefer one from the south or southwest. Willing to 
    travel for right vehicle.
    
    Chris Roche
    CRISTA::ROCHE
    285-3809
    Home 603-437-2117
    

    Any one have any info on mail order companys specializing in Chevy
    Camaro parts ???
    
    Thanks for any input
    
    chris
    

    Chris,
    
    There is a company called Classic Camaro located in California.  I've
    never ordered anything from them, but have their catalog and it's
    loaded with all kinds of parts.  Of course, you have to pay postage on
    the parts..so I use a local dealer Jack Hoover's Camaro Classics out of
    Fitchburg MA.. and his prices are very good... I always compare them to
    the catalog.. and I don't have to pay shipping.
    
    Anyways, Classic Camaro has original & reproduction parts going back to
    67 (I'm currently restoring a 67 camaro convertible).
    
    		Classic Camaro Parts & Accessories
    		17832 Gothard
    		Huntington Beach, CA 92647
    
    		1-800-854-1280
    
    Good luck!

    
    
          Does anyone know a parts store or a company that sells just
    camaro parts?  I need certain parts, that I want to buy new..Maybe
    a fan club for the camaro owners?
    
    
    Mike
    jupitr::mjubinville
    

    
    Mike,
    
    I have a friend who specializes in Camaro parts. He has the best prices
    and will deliver to anywhere in the country. Here it is;
    
    	Evergreen Muscle Car Supply
    	21030 - 84th Ave S
    	Kent, WA 98032
    	(206)872-9477
    	
    Bob Everett is the owner...Tell him I sent you
    
    Don Berry
    

    Rich Wojdak
    SUBSYS::WOJDAK
    237-6629
    
    
    Wanted - 1970 Chevelle passenger side fender - must be clean (NO dents,
    surface rust OK).

    
    WANTED:	Set of front coil springs for Big Block '67-'69 Camaro.
    
    CONTACT:	Don Berry
    		NWTIMA::BERRYDO
    		DTN 545-4539
    		Home (206)347-1431
    
    db
    

I'm looking to build a couple of spare motors for my race car and would be
interested in any of the following parts you might have collecting dust. 

454 four bolt blocks (passenger only, no truck or marine) no more then 60 over.

454 standard steel cranks.

Open chambered rectangular port heads.

Dart intakes and Fuildampr's

Holley dominator's
    
	Phil Berger
        DTN 223-2626
    	Railrd::berger_p

    Thought I'd try again, as it's been a year or better.  
    
    			Early Chevy (58-64) Rear End
    
    Ideally looking for complete carrier, set up w/3.70 or 4.11 posi
    
    Would settle for 3.70, 4.11, or 4.56 ring and pinion
    
    Have 3.55 posi in car now that I would be willing to trade, if
    necessary.
    
    		Any leads appreciated.....
    
    				Steve George
    				ICS::george
    				Dtn 223 4265
    
    Also looking for a re-installable "line-loc" type set up

    
    
    	Wanted, set of tall chrome valve covers for small block Chevy.
    
    	My short ones won't clear my new roller rockers.
    
    
    	Mark
    
    
    	ASABET::HAMEL
    	DTN 223-6336

    
    Looking for a good working, or solid rebuildable Quadrajet carb.
    Must be emissions era with EGR/PCV.  Might entertain possibility of a
    Holley spreadbore in the 600 CFM range - also emissions compatible.
    
    Looking to spend *short* money.  
    
    Send mail please.
    

Hi,

Currently looking for a couple of parts for my 67 camaro.

	1.  Windlace Endcap  .. only need the passenger side one.

	2.  Complete passing gear linkage kit
	    (powerglide transmission, 327 small block)

	

Thanks,


Cathi P
iago::provencal

	Would anyone happen to know where I could find some nice clean chrome
tail light bezels for a 1970 Nova?  I've looked in many of the repro parts catalogues
but have not seen anything there. I'd appreciate any leads.

thanks,
marc

           
    
    I'm looking for a Monte Carlo ss rear spoiler. Anyone happen 
    to know of one being parted out? None of the local yards have
    one at this time.
    
    /Bob  DTN:223-3242 (Mill)
      

    
    
    Rob L. Bussard
    Comet::Bussard
    DTN 522-2144
    CXO1-2
    
    Looking for a SB Chevy street dist.,  like a dual-point
    with vacuum...
    
    Also DESPERATELY need a stock '62 - 65 (Pref.  '64)  4 bbl
    air cleaner.  This unit will have a 1 1/4" tube coming from the
    bottom cover for the positive crankcase ventilation.  I have
    the stock 2 bbl.,  but need a 4 bbl.
    
    Also,  anyone heard of an overdrive rearend for the older Chevys?
    I understand that some of the Impala series may have had an over-
    drive to assist the Powerslide.....
    
    Many thanks,
    
    Rob

    Looking for two 8" x 15"  Corvette rally wheels or any type of
    aluminum wheels to mount a set of slicks. 
    
    
    John Malesky
    dtn 225-5110
    HOTLNE::MALESKY

    Well, the rust free '69 El Camino arrived Friday night, so now I'm
    trying to gather up a couple of missing parts:
    
    Front bumper with brackets and parking lights
    
    Core support (either a 68 or 69 will do).
    
    I'd also be interested in any other 69 Chevelle/El Camino parts.
    
    Chris

    
    	Anyone have a 12-bolt Chevy rear end for a 67-69 Camaro? Non posi
    is OK because i'm going to put a spool in it for racing. The car has
    the mono-leaf spring but i'll consider buying one for a multi-leaf
    setup. I don't want to pay more than $50-100 for one. I'm located in
    Maynard, MA.
    
    	Mark Higgins
    Phone 508-897-8754
    

    
    Mark,
    
    Those axles are in demand and bring big $$$ because of their width. Why
    not consider a 12 bolt out of a wider car like a Impalla or Caprice since 
    you will have to do some welding work on it anyway. Here is what it
    takes to make a 12 bolt live with slicks and a big block;
    
    Aftermarket axles - Do not get 28 splines. 35 is good, 40 is better
    Axle retention devices - The ends of the housing need to be cut off to
    	install. Easy to do in a lathe when narrowing.
    Spool - Buy at the same time as the axles with the same # of splines.
    Billet caps - The stock cast iron caps are not up to the task. These
    	must be custom fitted to your housing. Available from Mark
    	Williams.
    Welding - The tubes must be welded to the center section or they will
    	twist out the spot welds. If you plan on using ladder bars or
    	welding anything else onto the tubes - do it all at once. The welding
    	process causes warpage which must be corrected by cutting the ends
    	off and realigning them.
    Gears - Use Pro gears for racing only. DO NOT use for the street -
    	ever! If the car will see street use (won't be fun with a spool) 
    	use street gears.
    
    Total bill
    
    	Spool		$230
    	Axles		$380
    	Safety Hubs	$130
    	Billet Caps	$120
    	Machine Work	 $60
    	Welding		$400
    	Gear Setup	$175
    ________________________
    	total	      $1,495
    
    This is still about $1,000 cheaper than a similar 9 inch ford and
    weighs less too!
    
    If your serious about racing on a 12 bolt, don't try to do it in
    stages. It will cost you a LOT more in the long run (is that the voice
    of experience I hear?). Use only top quality parts and first class
    labor. Cheap can = BIG $$$$.
    
    Don B 

    WANTED: 4.11 Richmond Pro or Street gear set for 12 bolt GM rear.
            (used or new)
    
    Contact: John Malesky
             HOTLNE::MALESKY
             DTN 225-5110
             Home : (508)832-2984

    
    Wanted,
    
    Fiberglass Cowl Induction hood for a 70-81 Camaro.
    
    Also does anybody have any experience with Unlimited Products?
    I have heard some negitive things about their stuff. They are the
    cheapest, so I guess you get what you pay for.
    
    ASABET::HAMEL
    223-6336
    
    Thanks,
    
    mh
    

    Do you want the whole hood, or just the scoop (stock style)?
    
    I've dealt with Harwood before.  I'm going to have to (just HAVE
    to doncha know) buy another hood from them folks.  One of those 
    big ass pro stock deals.  :^)
           
    MadMike

    Regarding Unlimited Products...
    
    I have a complete front end for a '68 Camaro that I was very pleased
    with when it was on the car and would'nt hesitate to put it on another.
    I bought mine about ten years ago though...I'm sure the quality may
    have changed alot in that time period.
    
    jim
    

    Anyboby know how to get to Dobels Chevrolet? I need directions from
    495.
    
    Also, is Jack Hoover's Camaro still around, and where is he located?
    
    Thanks,
    
    Mark

    Dobles in Manchester NH?
    
    Take 495 to 95N
    
    95 N to 101W/295n (bear left at the split where 95 continues North
    toward Concord)
    
    Take NH exit 1 to South Willow St.
    
    Bear Right on ramp - right at top, first right at lights
    and your at Dobles Chevy....enter through the service area and the
    parts dept is halfway down the work bays on your left.
    
    

    Tom, I'm thinking you must mean Rt 495 to Rt 93 N to Rt 101W/Rt 293.
    Rt 495 to Rt 95 will bring you up to Maine.
    Wayne

    opps...yup 93 is correct...sorry....but those directions would have
    gotten you pretty close to my house!
    
    /tb/