Conference bgsdev::open3d

From your DECW$private_server_setup.com i see your Xserver is pretty out
of resources. The value of 370000 for DECW$SERVER_PAGE_FILE is per
ZLX(p)-E* card, so you should use 740000.

Also make sure that the DECW$SERVER... definitions are in the right
place inside DECW$private_server_setup.com
And check the SYSGEN parameters VIRTUALPAGECNT and WSMAX,
they must be equal or greater then 740000 resp. 20480

/Reinhard

	Hi Reinhard,

	In the following lines I'll write down the info you comment in
	you reply,and some more additional.Please,can you comment any
	other think you can see?

	Thanks for your help,

						/jls.

	INFO:

	a) SYSGEN PARAMETERS:

	VIRTUALPAGECNT = 1000000
	WSMAX	       = 65536
	PQL_MWSEXTENT  = 65536     ( Everyone can grow to wsmax)
	CHANNELCNT     = 256   (*)    

	(*) Relation with FILLM quota?. We're specifying the value 400
	for DECW$SERVER_FILE_LIMIT and uaf.See below lines.     


	b) DECW$PRIVATE_SERVER_SETUP.COM:

	The "define" lines,pointed in reply .0,are located after the 
	FINAL_SETUP_ENTRY: label.In fact,they are between the lines:

	$ ! Decw$server_default_visual_class == "3,4,0"
	 ....
	$ DECW$SERVER_DEFAULT_VISUAL_CLASS == "3,3"
        $ define/nolog/proc DECW$SERVER_FILE_LIMIT            400
	$ ....
        $ define/nolog/proc DECW$XPORT_SYNC_TIMEOUT           60000
	 ....
	$ ! Decw$server_connect_log
	
	c) Size of the system files:

	PAGEFILE.SYS => 525.000     (1)

	(1) Is necessary to extend to pagefile more?.I usually see a lot 
	of free space in the pagefile (problem time as well).

	SWAPFILE     =>  19.600

	d) Uaf quotas of the accounts: SYSTEM and POE.

	Note: POE is the username of the account that works in the alpha-
	station,running the graphic application:

	SYSTEM: 

	Maxjobs:         0  Fillm:       400  Bytlm:       100000
	Maxacctjobs:     0  Shrfillm:      0  Pbytlm:           0
	Maxdetach:       0  BIOlm:       150  JTquota:       4096
	Prclm:          10  DIOlm:       150  WSdef:        10240
	Prio:            4  ASTlm:       250  WSquo:        20480
	Queprio:         0  TQElm:       100  WSextent:     32768
	CPU:        (none)  Enqlm:      2000  Pgflquo:     370000


	POE:

	Maxjobs:         0  Fillm:       400  Bytlm:      1000000
	Maxacctjobs:     0  Shrfillm:      0  Pbytlm:           0
	Maxdetach:       0  BIOlm:      1500  JTquota:       4096
	Prclm:          20  DIOlm:      1500  WSdef:         8192
	Prio:            4  ASTlm:      1500  WSquo:        16384
	Queprio:         0  TQElm:       100  WSextent:     32768
	CPU:        (none)  Enqlm:      2000  Pgflquo:     400000
	
	

here some additional infos for you
(some of them are from the Open3D Release Notesa)

a) SYSGEN PARAMETERS:
   looks ok for me

b) position of definitions inside DECW$PRIVATE_SERVER_SETUP.COM:
  the template is prepared for a cluster setup, so looks somewhat tricky.
  If you are a standalone system: (node_list .eqs. "")
    the definitions should be inserted between $DO_DEFAULT: and the next exit
  If you are a cluster member: (node_list must be appropriatly defined)
    the definitions should be after label $DO_your_nodename:

c) Size of the system files:
   - pagefile size
     the pagefile must not be as large as the corresponding quotas
     525.000 blocks may be enough if there are no higher requirements from
     other processes
   - SWAPFILE: does not matter

d) Uaf quotas of the accounts:
   that's waht i forgot in my reply .1:
   the decwindow server, the SYSTEM account and the user account
   should have same minimum pagefile quotas and same minimum wsextent
   (i.e. pagefile quotas >= 740000,  wsextent >= 20480)

Hope that helps, good luck
/Reinhard

    
    	Thanks Reinhard,
    
    	We'll try with the new quotas suggested...
    
    	Regards,
    
    						/jls.
    
    	PS: I'll change the location of definitions in decw$private_server_
    	setup file,instead looking the process quotas are the ones
    	expected.I'll move them from the actual location to "Do_default".

    
    	Hi again,
    
    	After changing the quotas and place definition in  decw$server_
    private_setup file,the problem remains.In the last cases (two from 
    last report) we've been able to "recover" the situation restarting 
    the server (@sys$startup:decw$startup restart => new login box),instead 
    of rebooting the system.By the way,we've tried to restart mwm (stopping 
    the actual and creating a new one),at problem tiem,without any effect 
    in the problem.
    
    	Any comment,hint,sugestion...will be very appreciated!	
    
    	Which can be the main product related to the problem.....open3d or
        decwindows (server) or motif ?
    
    
    	Thanks in advance,
    						/jls.
    

    
    	The problem has been escalated to IPMT.
    
    	/jls.