| Title: | DECmcc user notes file. Does not replace IPMT. |
| Notice: | Use IPMT for problems. Newsletter location in note 6187 |
| Moderator: | TAEC::BEROUD |
| Created: | Mon Aug 21 1989 |
| Last Modified: | Wed Jun 04 1997 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 6497 |
| Total number of notes: | 27359 |
I have been experiencing problems with the exporter on T1.2.7
Whenever I try to export from the FCL I get messages like those
attached below.
Any suggestions...
SH QUEUE EXPORT_Q/FULL/ALL
Batch queue EXPORT_Q, available, on RGNET4::
/AUTOSTART_ON=(RGNET4::) /BASE_PRIORITY=4 /JOB_LIMIT=5 /OWNER=[SYSTEM]
/PROTECTION=(S:E,O:D,G:R,W:W)
Entry Jobname Username Status
----- ------- -------- ------
984 MCC_EXPORTER_BACKGROUND
SYSTEM Executing
Submitted 14-MAY-1992 14:52 /KEEP
/PARAM=("DISK$USER_DISK:[MCC_USER]MCC_EXPORT.RDB") /NOPRINT
/PRIORITY=100 /RESTART=EXPORT_Q
File: _RGNET4$DKA0:[SYSCOMMON.SYSMGR]MCC_EXPORTER_BACKGROUND.COM;3
$ MAN/ENTER
DECmcc (T1.2.7)
@EXPORT_MRO2AB
Node4 MRO2AB
AT 14-MAY-1992 14:59:49
Background exporting process is not set up
Node4 MRO2AB Line SYN-*
AT 14-MAY-1992 14:59:56
Background exporting process is not set up
Node4 MRO2AB Circuit SYN-*
AT 14-MAY-1992 14:59:58
Background exporting process is not set up
Node4 MRO2AB Line ETHERNET
AT 14-MAY-1992 14:59:59
Background exporting process is not set up
Node4 MRO2AB Circuit ETHERNET
AT 14-MAY-1992 15:00:01
Background exporting process is not set up
MCC> EXIT
| T.R | Title | User | Personal Name | Date | Lines |
|---|---|---|---|---|---|
| 2998.1 | did you do the setup? | TOOK::CALLANDER | MCC = My Constant Companion | Thu May 14 1992 16:38 | 3 |
did you run all of the set up procedures as explained in the
export manual?
| |||||
| 2998.2 | check "export target" argument | TOOK::SHMUYLOVICH | Fri May 15 1992 08:58 | 7 | |
What "export target" argument do you use in the Export command?
It must match the parameter submitted for the background process.
SAm
| |||||
| 2998.3 | This is the command file, target matches... | RGNET8::BOUTHIETTE | Feed your lust for life!! | Fri May 15 1992 09:21 | 17 |
! ! EXPORT NODE4 MRO2AB EXPORT TARGET = - DISK$USER_DISK:[MCC_USER]MCC_EXPORT.RDB,EXPORT PERIOD = :30 ! EXPORT NODE4 MRO2AB LINE SYN-* EXPORT TARGET = - DISK$USER_DISK:[MCC_USER]MCC_EXPORT.RDB,EXPORT PERIOD = :15 ! EXPORT NODE4 MRO2AB CIRCUIT SYN-* EXPORT TARGET = - DISK$USER_DISK:[MCC_USER]MCC_EXPORT.RDB,EXPORT PERIOD = :15 ! EXPORT NODE4 MRO2AB LINE ETHERNET EXPORT TARGET = - DISK$USER_DISK:[MCC_USER]MCC_EXPORT.RDB,EXPORT PERIOD = :15 ! EXPORT NODE4 MRO2AB CIRCUIT ETHERNET EXPORT TARGET = - DISK$USER_DISK:[MCC_USER]MCC_EXPORT.RDB,EXPORT PERIOD = :15 ! | |||||
| 2998.4 | re .1 | RGNET8::BOUTHIETTE | Feed your lust for life!! | Fri May 15 1992 09:47 | 5 |
Re: .1
I followed all steps in the Exporter documentation ...
Jb.
| |||||