| Title: | *OLD* ALL-IN-1 (tm) Support Conference |
| Notice: | Closed - See Note 4331.l to move to IOSG::ALL-IN-1 |
| Moderator: | IOSG::PYE |
| Created: | Thu Jan 30 1992 |
| Last Modified: | Tue Jan 23 1996 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 4343 |
| Total number of notes: | 18308 |
I have a problem with ALL-IN-1 V3.0.
When I send a mail from ALL-IN-1 to A1MAIL the return address is set as
From: ARUN DHURI ("ARUNPAPER MAIL")
(ALL-IN-1 and A1MAIL are on different nodes, so message goes through MR)
Because of this recipient can't use Reply command to just reply to received
mail.
When I send a mail from ALL-IN-1 to VMSmail the return address in top "FROM"
is shown correctly. But in the content part "From" the same is seen within < >
as:-
From: NAME: ARUN DHURI
FUNC: EIS-EXPORTS
TEL: 837-0333 <ARUNPAPER MAIL>
Here ARUN is my account name. Does anybody know the solution to this???
- Arun Dhuri
| T.R | Title | User | Personal Name | Date | Lines |
|---|---|---|---|---|---|
| 1857.1 | DDS UA ? | UTRTSC::SCHOLLAERT | AJAX beats Feyenoord again and again | Fri Nov 27 1992 08:04 | 27 |
Arun,
Looks like your DDS UA for ALL-IN-1 not set up properly.
and mailbox part.
Try within MBMAN>show dds ua /full /NAME=OA$<nodename>$ALLIN1
Should look like:
SHOW DDS UA /FULL /NAME=OA$SSOIOS$ALLIN1
Name : OA$SSOIOS$ALLIN1
Master copy owning node : SSOIOS
MHS/VMS address number : 1
MHS/VMS address part : SSOIOS
MHS mailbox : A1
MHS User identifier : MANAGER
Try within ALL-IN-1 <GET OA$DDS_AREA_ROUTE
Return something like: @A1@SSOIOS
If not, try something like this...
WRITE CHANGE useragent commname = "OA$<node>$ALLIN1" ,-
log$oa$mti_mailbx, mtanode2 = oa$primary_node
Regards,
Jan
| |||||
| 1857.2 | OA$MTI_AREA ? | DELBOY::DORANA | Tue Dec 01 1992 21:12 | 7 | |
Try the logical OA$MTI_AREA
should be something like "A1 at NODE"
Cheers,
Andy
| |||||
| 1857.3 | OA$MTI_AREA isn't involved | AIMTEC::WICKS_A | Liverpool 4 Norwich 1 | Tue Dec 01 1992 21:20 | 8 |
Re. 2,
No I'm sure Jan is right in .1. The logical OA$MTI_AREA isn't used to build
OA$DDS_AREA_ROUTE.
Regards,
Andrew.D.Wicks
| |||||
| 1857.4 | Thanks a lot | FORTY2::DHURI | Wed Dec 02 1992 07:04 | 9 | |
Thanks Jane!
I was in loop. I was modifying my (sub) DDS entries all the time.
Thanks a lot you broke the loop. I deleted the DDS UA entry for my
ALL-IN-1 and built it again. It works fine now.
Thanks again.
- Arun
| |||||